| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| The L2CAP receive data buffer for L2CAP packets is restricted to packet sizes smaller than the maximum supported packet size. Receiving a packet that exceeds the restricted buffer length may cause a crash. A hard reset is required to recover the crashed device. |
| Due to an unchecked buffer length, a specially crafted L2CAP packet can cause a buffer overflow. This buffer overflow triggers an assert, which results in a temporary denial of service.
If a watchdog timer is not enabled, a hard reset is required to recover the device. |
| When decoding a frame for a SANM file (ANIM v0 variant), the decoded data can be larger than the buffer allocated for it.
Frames encoded with codec 48 can specify their resolution (width x height). A buffer of appropriate size is allocated depending on the resolution.
This codec can encode the frame contents using a run-length encoding algorithm. There are no checks that the decoded frame fits in the allocated buffer, leading to a heap-buffer-overflow.
process_frame_obj initializes the buffers based on the frame resolution:
We recommend upgrading to version 8.0 or beyond. |
| When parsing the header for a DHAV file, there's an integer underflow in offset calculation that leads to reading the duration from before the start of the allocated buffer.
If we load a DHAV file that is larger than MAX_DURATION_BUFFER_SIZE bytes (0x100000) for example 0x101000 bytes, then at [0] we have size = 0x101000. At [1] we have end_buffer_size = 0x100000, and at [2] we have end_buffer_pos = 0x1000.
The loop then scans backwards through the buffer looking for the dhav tag; when it is found, we'll calculate end_pos based on a 32-bit offset read from the buffer.
There is subsequently a check [3] that end_pos is within the section of the file that has been copied into end_buffer, but it only correctly handles the cases where end_pos is before the start of the file or after the section copied into end_buffer, and not the case where end_pos is within the the file, but before the section copied into end_buffer. If we provide such an offset, (end_pos - end_buffer_pos) can underflow, resulting in the subsequent access at [4] occurring before the beginning of the allocation.
We recommend upgrading to version 8.0 or beyond. |
| When calculating the content path in handling of MPEG-DASH manifests, there's an out-of-bounds NUL-byte write one byte past the end of the buffer.When we call xmlNodeGetContent below [0], it returns a buffer precisely allocated to match the string length, using strdup internally. If this buffer is not an empty string, it is assigned to root_url at [1].If the last (non-NUL) byte in this buffer is not '/' then we append '/' in-place at [2]. This will write two bytes into the buffer, starting at the last valid byte in the buffer, writing the NUL byte beyond the end of the allocated buffer.
We recommend upgrading to version 8.0 or beyond. |
| Affected products contain a vulnerability in the device cloud rpc command handling process that could allow remote attackers to take control over arbitrary devices connected to the cloud. |
| A vulnerability, which was classified as critical, has been found in Zend.To up to 6.10-6 Beta. This issue affects the function exec of the file NSSDropoff.php. The manipulation of the argument file_1 leads to os command injection. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used. Upgrading to version 6.10-7 is able to address this issue. It is recommended to upgrade the affected component. This affects a rather old version of the software. The vendor recommends updating to the latest release. Additional countermeasures have been added in 6.15-8. |
| MicroDicom
DICOM Viewer suffers from an out-of-bounds write vulnerability. Remote attackers are able to exploit this issue to potentially execute arbitrary code on affected installations of DICOM Viewer. User interaction is required to exploit the vulnerability in that the user must either visit a malicious website or open a malicious DICOM file locally. |
| A command injection vulnerability has been identified in bwdpi. A remote, authenticated attacker could leverage this vulnerability to potentially execute arbitrary commands, leading to the device executing unintended instructions.
Refer to the 'Security Update for ASUS Router Firmware' section on the ASUS Security Advisory for more information. |
| An authentication-bypass vulnerability exists in AiCloud. This vulnerability can be triggered by an unintended side effect of the Samba functionality, potentially leading to allow execution of specific functions without proper authorization.
Refer to the Security Update for ASUS Router Firmware section on the ASUS Security Advisory for more information. |
| An OS Command Injection vulnerability in the Admin panel in Curo UC300 5.42.1.7.1.63R1 allows local attackers to inject arbitrary OS Commands via the "IP Addr" parameter. |
| In Flowmon versions prior to 12.5.5, a vulnerability has been identified that allows a user with administrator privileges and access to the management interface to execute additional unintended commands within scripts intended for troubleshooting purposes. |
| CWE-78: Improper Neutralization of Special Elements used in an OS Command ('OS Command Injection')
vulnerability exists that could cause remote control over the charging station when an authenticated user
modifies configuration parameters on the web server. |
| Certain models of NVR developed by Digiever has an OS Command Injection vulnerability, allowing authenticated remote attackers to inject arbitrary OS commands and execute them on the device. |
| GitHub Kanban MCP Server is a Model Context Protocol (MCP) server for managing GitHub issues in Kanban board format and streamlining LLM task management. Version 0.3.0 of the MCP Server is written in a way that is vulnerable to command injection vulnerability attacks as part of some of its MCP Server tool definition and implementation. The MCP Server exposes the tool `add_comment` which relies on Node.js child process API `exec` to execute the GitHub (`gh`) command, is an unsafe and vulnerable API if concatenated with untrusted user input. As of time of publication, no known patches are available. |
| OS Command Injection in iSTAR Ultra products web application allows an authenticated attacker to gain even more privileged access ('root' user) to the device firmware. |
| Command injection vulnerability exists in the “Logging” page of the web-based configuration utility. An authenticated user with low privileged network access for the configuration utility can execute arbitrary commands on the underlying OS to obtain root SSH access to the TropOS 4th Gen device. |
| The “Diagnostics Tools” page of the web-based configuration utility does not properly validate user-controlled input, allowing an authenticated user with high privileges to inject commands into the command shell of the TropOS 4th Gen device. The injected commands can be exploited to execute several set-uid (SUID) applications to ultimately gain root access to the TropOS device. |
| A vulnerability has been found in D-Link DI-8100, DI-8100G, DI-8200, DI-8200G, DI-8003 and DI-8003G 16.07.26A1/17.12.20A1/19.12.10A1. Affected by this vulnerability is the function sub_4621DC of the file usb_paswd.asp of the component jhttpd. The manipulation of the argument hname leads to os command injection. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used. |
| A vulnerability was found in D-Link DI-8100G, DI-8200G and DI-8003G 17.12.20A1/19.12.10A1. Affected by this issue is the function sub_433F7C of the file version_upgrade.asp of the component jhttpd. The manipulation of the argument path results in os command injection. The attack may be launched remotely. The exploit has been made public and could be used. |
