| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
HID: hid-goodix-spi: validate report size to prevent stack buffer overflow
goodix_hid_set_raw_report() builds a protocol frame in a 128-byte stack
buffer (tmp_buf), writing an 11-12 byte header followed by the
caller-supplied report data. The HID core caps report size at
HID_MAX_BUFFER_SIZE (16384) by default, while the driver does not set
hid_ll_driver.max_buffer_size and performs no bounds checking before
copying the payload:
memcpy(tmp_buf + tx_len, buf, len);
A hidraw SET_REPORT ioctl with a report larger than ~116 bytes
overflows the stack buffer.
Add a size check after constructing the header, rejecting reports that
would exceed the buffer capacity.
Discovered by Atuin - Automated Vulnerability Discovery Engine. |
| In the Linux kernel, the following vulnerability has been resolved:
partitions: aix: bound the pp_count scan to the ppe array
aix_partition() reads the physical volume descriptor into a fixed-size
struct pvd and then scans its physical-partition-extent array:
int numpps = be16_to_cpu(pvd->pp_count);
...
for (i = 0; i < numpps; i += 1) {
struct ppe *p = pvd->ppe + i;
...
lp_ix = be16_to_cpu(p->lp_ix);
pvd points at a single kmalloc()'d struct pvd whose ppe[] member holds a
fixed ARRAY_SIZE(pvd->ppe) (1016) entries, but the loop runs up to the
on-disk pp_count. pp_count is an unvalidated __be16 read straight from
the descriptor, so a crafted AIX image with pp_count larger than 1016
drives the loop to read pvd->ppe[i] past the end of the allocation (up
to 65535 entries, ~2 MB out of bounds).
The partition scan runs without mounting anything, when a block device
with a crafted AIX/IBM partition table appears (an attacker-supplied
image attached with losetup -P, or a device auto-scanned by udev), via
msdos_partition() -> aix_partition().
Clamp the scan to the number of entries the ppe[] array can hold. |
| IBM Langflow OSS 1.0.0 through 1.10.1 Lanflow OSS contains an unauthenticated remote code execution vulnerability in the public flow build endpoint ( /api/v1/build_public_tmp/{flow_id}/flow ). The vulnerability stems from an incomplete denylist in the validate_public_flow_no_code_execution() function that fails to block several code-execution agent components including OpenDsStarAgent, CodeActAgentSmolagents, and CSVAgent. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: limit injected antenna index in ieee80211_parse_tx_radiotap
When parsing the radiotap header of an injected frame,
ieee80211_parse_tx_radiotap() uses the IEEE80211_RADIOTAP_ANTENNA value
directly as a shift count:
info->control.antennas |= BIT(*iterator.this_arg);
*iterator.this_arg is an 8-bit value taken straight from the frame
supplied by userspace, so BIT() can be asked to shift by up to 255. That
is undefined behaviour on the unsigned long and is reported by UBSAN:
UBSAN: shift-out-of-bounds in net/mac80211/tx.c:2174:30
shift exponent 235 is too large for 64-bit type 'unsigned long'
Call Trace:
ieee80211_parse_tx_radiotap+0xadb/0x1950 net/mac80211/tx.c:2174
ieee80211_monitor_start_xmit+0xb1f/0x1250 net/mac80211/tx.c:2451
...
packet_sendmsg+0x3eb6/0x50f0 net/packet/af_packet.c:3109
info->control.antennas is a 2-bit bitmap (u8 antennas:2), so only antenna
indices 0 and 1 can ever be represented. Ignore any larger value instead
of shifting out of bounds. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: scsi_transport_fc: Widen FPIN pname walker counter to u32
An adjacent Fibre Channel fabric actor that can deliver an FPIN ELS
frame to an lpfc or qla2xxx Linux initiator can trigger a non-return in
the generic FC transport. This is not a local userspace or IP network
path; the attacker must be able to inject fabric traffic, for example as
a compromised switch or fabric controller, or as a same-zone N_Port on a
fabric that permits source spoofing.
The Link-Integrity and Peer-Congestion FPIN walkers used a u8 loop
counter against the 32-bit on-wire pname_count field, and did not bound
pname_count by the descriptor body already validated by the TLV walker.
A pname_count of 256 therefore wraps the counter and keeps the loop
condition true indefinitely.
Factor the shared pname_list[] walk into one helper, widen the counter
to u32, and clamp pname_count against the entries that fit in the
descriptor body before iterating. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: property: Reject u32 wrap in tb_property_entry_valid()
entry->value is u32 and entry->length is u16; the sum is performed in
u32 and wraps. A malicious XDomain peer can pick
value = 0xffffff00, length = 0x100 so the sum 0x100000000 wraps to 0
and passes the > block_len check. tb_property_parse() then passes
entry->value to parse_dwdata() as a dword offset into the property
block, reading attacker-directed memory far past the allocation.
For TEXT-typed entries with the "deviceid" or "vendorid" keys this
lands in xd->device_name / xd->vendor_name and is readable back via
the per-XDomain device_name / vendor_name sysfs attributes; the leak
is NUL-bounded (kstrdup() stops at the first zero byte) and
untargeted (the attacker picks a delta, not an absolute address).
DATA-typed entries are parsed into property->value.data but not
generically surfaced to userspace.
Use check_add_overflow() so a wrapped sum is rejected. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: iptfs: reset runtime state when cloning SAs
iptfs_clone_state() clones the IPTFS mode data with kmemdup(). This
copies runtime objects which must not be shared with the original SA,
including the embedded sk_buff_head, hrtimers, spinlock, and in-flight
reassembly/reorder state.
If xfrm_state_migrate() fails after clone_state() but before the later
init_state() call has reinitialized those fields, the cloned state can be
destroyed by xfrm_state_gc_task() with list and timer state copied from the
original SA. With queued packets this lets the clone splice and free skbs
owned by the original IPTFS queue, leading to use-after-free and
double-free reports in iptfs_destroy_state() and skb release paths.
Reinitialize the clone's runtime state before publishing it through
x->mode_data. Because clone_state() now publishes a destroyable mode_data
object before init_state(), take the mode callback module reference there.
Avoid taking it again from __iptfs_init_state() for the same object. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: hci: fix out-of-bounds read in HCP header parsing
Both nfc_hci_recv_from_llc() and nci_hci_data_received_cb() read
packet->header from skb->data at function entry without first checking
that the buffer holds at least one byte. A malicious NFC peer can send
a 0-byte HCP frame that passes through the SHDLC layer and reaches
these functions, causing an out-of-bounds heap read of packet->header.
The same 0-byte frame, if queued as a non-final fragment, also causes
the reassembly loop to underflow msg_len to UINT_MAX, triggering
skb_over_panic() when the reassembled skb is written.
Fix this by adding a pskb_may_pull() check at the entry of each
function before packet->header is first accessed. The existing
pskb_may_pull() checks before the reassembled hcp_skb is cast to
struct hcp_packet remain in place to guard the 2-byte HCP message
header. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: validate extension header length before copying to cmsg
ip6_datagram_recv_specific_ctl() builds IPV6_{HOPOPTS,DSTOPTS,RTHDR}
cmsgs (and their IPV6_2292* legacy counterparts) by trusting the
on-wire hdrlen byte (ptr[1]) when computing the put_cmsg() length.
The length was validated only at parse time (ipv6_parse_hopopts(),
etc.). An nftables payload-write expression can rewrite hdrlen after
parsing and before the skb reaches recvmsg; the write itself is
in-bounds but put_cmsg() then reads up to ((hdrlen+1) << 3) = 2040
bytes from an 8-byte header. nftables is reachable from an
unprivileged user namespace, so this is an unprivileged
slab-out-of-bounds read:
BUG: KASAN: slab-out-of-bounds in put_cmsg+0x3ac/0x540
put_cmsg+0x3ac/0x540
udpv6_recvmsg+0xca0/0x1250
sock_recvmsg+0xdf/0x190
____sys_recvmsg+0x1b1/0x620
Add ipv6_get_exthdr_len() which validates that at least two bytes
are accessible before reading the hdrlen field, then checks the
computed length against skb_tail_pointer(skb), returning 0 on
failure. Extension headers are kept in the linear skb area by
pskb_may_pull() during input, so skb_tail_pointer() is the correct
bound.
Use ipv6_get_exthdr_len() at all non-AH call sites: the five
standalone cmsg blocks (HbH, 2292HbH, 2292DSTOPTS x2, 2292RTHDR)
and the three standard cases in the extension-header walk loop
(DSTOPTS, ROUTING, default). AH retains an inline bounds check
because its length formula differs ((ptr[1]+2)<<2).
The walk loop also gets a pre-read bounds check at the top to
validate ptr before any case accesses ptr[0] or ptr[1].
When the walk loop detects a corrupted header, return from the
function instead of continuing to process later socket options. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: chemical: mhz19b: reject oversized serial replies
mhz19b_receive_buf() appends each serdev chunk into the fixed
MHZ19B_CMD_SIZE receive buffer and advances buf_idx by len without
checking that the chunk fits in the remaining space. A large callback
can therefore overflow st->buf before the command path validates the
reply.
Reset the reply state before each command and reject oversized serial
replies before copying them into the fixed buffer. When an oversized
reply is detected, wake the waiter and report -EMSGSIZE instead of
overwriting st->buf. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Check PSC request indices against the actual size of the buffer
When processing Page State Change (PSC) requests, validate the PSC buffer
against the effective size of the scratch area, which could be less than
the maximum size if the guest provided a pointer that isn't exactly at the
start of the GHCB shared buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm/tcpci_maxim: validate header NDO against RX_BYTE_CNT
A broken/malicious port can transmit a CRC-valid frame whose header
advertises up to seven data objects but whose body carries fewer than
that. Check for this, and rightfully reject the message, instead of
reading from uninitialized stack memory. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: l2cap: clear chan->ident on ECRED reconfiguration success
l2cap_ecred_reconf_rsp() returns early on success without clearing
chan->ident. Every other L2CAP response handler (l2cap_ecred_conn_rsp,
l2cap_le_connect_rsp, l2cap_config_rsp) clears chan->ident after a
successful transaction to prevent the channel from matching subsequent
responses with the recycled ident value.
A remote attacker that completed a reconfiguration as the peer can
replay a failure response with the stale ident, causing the kernel to
match and destroy the already-established channel via
l2cap_chan_del(chan, ECONNRESET).
Clear chan->ident for all matching channels on success, and harden the
failure path by using l2cap_chan_hold_unless_zero() consistent with
other L2CAP handlers (l2cap_le_command_rej, __l2cap_get_chan_by_ident). |
| Jan through 0.8.4, fixed in commit 3e1c1e7, contains a CORS misconfiguration vulnerability in its local API server that allows network-adjacent attackers to bypass trusted host restrictions by exploiting the server's replacement of user-configured trusted hosts with a wildcard that reflects arbitrary origins with credentials. Attackers on the local network or using DNS rebinding can reach the unauthenticated OpenAI-compatible API to perform inference, enumerate models, invoke MCP tools, and read cross-origin responses. |
| Heap buffer overflow in libyuv in Google Chrome on Windows prior to 150.0.7871.125 allowed a remote attacker to execute arbitrary code inside a sandbox via a crafted video file. (Chromium security severity: High) |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: iscsi: Bound iscsi_encode_text_output() appends to rsp_buf
iscsi_encode_text_output() concatenates "key=value\0" records into
login->rsp_buf, an 8192-byte kzalloc(MAX_KEY_VALUE_PAIRS) buffer
allocated in iscsit_alloc_login_setup_buffer(). The three sprintf() call
sites in this function (lines 1398, 1411, 1424 in v7.1-rc2) never check
the remaining buffer capacity:
*length += sprintf(output_buf, "%s=%s", er->key, er->value);
*length += 1;
output_buf = textbuf + *length;
The 8192-byte ceiling at iscsi_target_check_login_request() bounds the
*input* Login PDU payload, but a single PDU can carry up to 2048 minimal
four-byte "a=b\0" pairs, each unknown key expanding to a 16-byte
"a=NotUnderstood\0" output record via iscsi_add_notunderstood_response().
2048 * 16 = 32 KiB of output into an 8 KiB buffer, producing a ~24 KiB
heap overrun in the kmalloc-8k slab.
The fix introduces a static iscsi_encode_text_record() helper that uses
snprintf() with a per-call bounds check against the remaining buffer,
and threads a u32 textbuf_size parameter through
iscsi_encode_text_output(). Both call sites in
iscsi_target_handle_csg_zero() (PHASE_SECURITY) and
iscsi_target_handle_csg_one() (PHASE_OPERATIONAL) pass
MAX_KEY_VALUE_PAIRS. On overflow the encoder logs the condition, calls
iscsi_release_extra_responses() to drop queued records, and returns -1;
both caller sites now emit ISCSI_STATUS_CLS_INITIATOR_ERR /
ISCSI_LOGIN_STATUS_INIT_ERR via iscsit_tx_login_rsp() before returning,
so the initiator sees an explicit failed-login response rather than a
silent connection drop. (Prior to this patch only the PHASE_OPERATIONAL
caller did that; the PHASE_SECURITY caller is converted to the same
shape.) |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: rpl: fix hdrlen overflow in ipv6_rpl_srh_decompress()
ipv6_rpl_srh_decompress() computes:
outhdr->hdrlen = (((n + 1) * sizeof(struct in6_addr)) >> 3);
hdrlen is __u8. For n >= 127 the result exceeds 255 and silently
truncates. With n=127 (cmpri=15, cmpre=15, pad=0, hdrlen=16):
(128 * 16) >> 3 = 256, truncated to 0 as __u8
The caller in ipv6_rpl_srh_rcv() then places the compressed header
at buf + ((ohdr->hdrlen + 1) << 3). With hdrlen=0 this is buf + 8,
but the decompressed region occupies buf[0..2055] (8-byte header
plus 128 full addresses). The compressed header overlaps the
decompressed data, and ipv6_rpl_srh_compress() writes into this
overlap, corrupting the routing header of the forwarded packet.
The existing guard at exthdrs.c:546 checks (n + 1) > 255, which
prevents n+1 from overflowing unsigned char (the segments_left
field), but does not prevent the computed hdrlen from overflowing
__u8. n=127 passes because 128 <= 255, yet hdrlen=256 does not
fit.
Tighten the bound to (n + 1) > 127. This caps n at 126, giving
hdrlen = (127 * 16) >> 3 = 254, which fits in __u8. The compressed
header then lands at buf + ((254 + 1) << 3) = buf + 2040, exactly
past the decompressed region (buf[0..2039]). No overlap. 127
segments is well beyond any realistic RPL deployment. |
| Out-of-bounds Write, Integer Underflow (Wrap or Wraparound) vulnerability in Apache NimBLE BASS service.
Improper validation when parsing BASS service "Add Source" and "Modify Source" operation PDU could results in stack buffer overflow or arbitrary out-of-bound read.
This can be triggered by nearby devices over Bluetooth connection, however pairing is required prior to accessing BASS service, which depending on device configuration may or may not require user action.
This issue affects Apache NimBLE: through 1.9.0.
Users are recommended to upgrade to version 1.10.0, which fixes the issue. |
| Buffer Copy without Checking Size of Input ('Classic Buffer Overflow') vulnerability in Apache NimBLE.
The HCI socket transport did not check whether a received HCI event would fit the configured event pool before copying it, allowing a buffer overflow. Severity is low: exploitation requires either a misconfigured pool size or a malicious/compromised controller on the other end of the HCI socket link, not over-the-air Bluetooth access.
This issue affects Apache NimBLE: through 1.9.0.
Users are recommended to upgrade to version 1.10.0, which fixes the issue. |
| U-Boot before 2026.07-rc2 contains a buffer overflow vulnerability in nfs_readlink_reply() (net/nfs-common.c) when CONFIG_CMD_NFS is enabled, allowing a malicious or compromised NFS server to overflow the 2048-byte nfs_path_buff buffer by returning multiple relative symlink targets that are appended without cumulative length validation. Attackers can send two or more READLINK responses containing relative symlink targets of approximately 1100 bytes each to corrupt adjacent BSS variables including nfs_server_ip, nfs_server_mount_port, nfs_server_port, nfs_our_port, nfs_state, and rpc_id, potentially achieving memory corruption and control over the NFS client state machine. |
