| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm: mxsfb: Fix NULL pointer dereference
mxsfb should not ever dereference the NULL pointer which
drm_atomic_get_new_bridge_state is allowed to return.
Assume a fixed format instead. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: single: fix potential NULL dereference
Added checking of pointer "function" in pcs_set_mux().
pinmux_generic_get_function() can return NULL and the pointer
"function" was dereferenced without checking against NULL.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/region: Fix null pointer dereference for resetting decoder
Not all decoders have a reset callback.
The CXL specification allows a host bridge with a single root port to
have no explicit HDM decoders. Currently the region driver assumes there
are none. As such the CXL core creates a special pass through decoder
instance without a commit/reset callback.
Prior to this patch, the ->reset() callback was called unconditionally when
calling cxl_region_decode_reset. Thus a configuration with 1 Host Bridge,
1 Root Port, and one directly attached CXL type 3 device or multiple CXL
type 3 devices attached to downstream ports of a switch can cause a null
pointer dereference.
Before the fix, a kernel crash was observed when we destroy the region, and
a pass through decoder is reset.
The issue can be reproduced as below,
1) create a region with a CXL setup which includes a HB with a
single root port under which a memdev is attached directly.
2) destroy the region with cxl destroy-region regionX -f. |
| In the Linux kernel, the following vulnerability has been resolved:
i40e: Fix kernel crash during module removal
The driver incorrectly frees client instance and subsequent
i40e module removal leads to kernel crash.
Reproducer:
1. Do ethtool offline test followed immediately by another one
host# ethtool -t eth0 offline; ethtool -t eth0 offline
2. Remove recursively irdma module that also removes i40e module
host# modprobe -r irdma
Result:
[ 8675.035651] i40e 0000:3d:00.0 eno1: offline testing starting
[ 8675.193774] i40e 0000:3d:00.0 eno1: testing finished
[ 8675.201316] i40e 0000:3d:00.0 eno1: offline testing starting
[ 8675.358921] i40e 0000:3d:00.0 eno1: testing finished
[ 8675.496921] i40e 0000:3d:00.0: IRDMA hardware initialization FAILED init_state=2 status=-110
[ 8686.188955] i40e 0000:3d:00.1: i40e_ptp_stop: removed PHC on eno2
[ 8686.943890] i40e 0000:3d:00.1: Deleted LAN device PF1 bus=0x3d dev=0x00 func=0x01
[ 8686.952669] i40e 0000:3d:00.0: i40e_ptp_stop: removed PHC on eno1
[ 8687.761787] BUG: kernel NULL pointer dereference, address: 0000000000000030
[ 8687.768755] #PF: supervisor read access in kernel mode
[ 8687.773895] #PF: error_code(0x0000) - not-present page
[ 8687.779034] PGD 0 P4D 0
[ 8687.781575] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 8687.785935] CPU: 51 PID: 172891 Comm: rmmod Kdump: loaded Tainted: G W I 5.19.0+ #2
[ 8687.794800] Hardware name: Intel Corporation S2600WFD/S2600WFD, BIOS SE5C620.86B.0X.02.0001.051420190324 05/14/2019
[ 8687.805222] RIP: 0010:i40e_lan_del_device+0x13/0xb0 [i40e]
[ 8687.810719] Code: d4 84 c0 0f 84 b8 25 01 00 e9 9c 25 01 00 41 bc f4 ff ff ff eb 91 90 0f 1f 44 00 00 41 54 55 53 48 8b 87 58 08 00 00 48 89 fb <48> 8b 68 30 48 89 ef e8 21 8a 0f d5 48 89 ef e8 a9 78 0f d5 48 8b
[ 8687.829462] RSP: 0018:ffffa604072efce0 EFLAGS: 00010202
[ 8687.834689] RAX: 0000000000000000 RBX: ffff8f43833b2000 RCX: 0000000000000000
[ 8687.841821] RDX: 0000000000000000 RSI: ffff8f4b0545b298 RDI: ffff8f43833b2000
[ 8687.848955] RBP: ffff8f43833b2000 R08: 0000000000000001 R09: 0000000000000000
[ 8687.856086] R10: 0000000000000000 R11: 000ffffffffff000 R12: ffff8f43833b2ef0
[ 8687.863218] R13: ffff8f43833b2ef0 R14: ffff915103966000 R15: ffff8f43833b2008
[ 8687.870342] FS: 00007f79501c3740(0000) GS:ffff8f4adffc0000(0000) knlGS:0000000000000000
[ 8687.878427] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8687.884174] CR2: 0000000000000030 CR3: 000000014276e004 CR4: 00000000007706e0
[ 8687.891306] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8687.898441] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 8687.905572] PKRU: 55555554
[ 8687.908286] Call Trace:
[ 8687.910737] <TASK>
[ 8687.912843] i40e_remove+0x2c0/0x330 [i40e]
[ 8687.917040] pci_device_remove+0x33/0xa0
[ 8687.920962] device_release_driver_internal+0x1aa/0x230
[ 8687.926188] driver_detach+0x44/0x90
[ 8687.929770] bus_remove_driver+0x55/0xe0
[ 8687.933693] pci_unregister_driver+0x2a/0xb0
[ 8687.937967] i40e_exit_module+0xc/0xf48 [i40e]
Two offline tests cause IRDMA driver failure (ETIMEDOUT) and this
failure is indicated back to i40e_client_subtask() that calls
i40e_client_del_instance() to free client instance referenced
by pf->cinst and sets this pointer to NULL. During the module
removal i40e_remove() calls i40e_lan_del_device() that dereferences
pf->cinst that is NULL -> crash.
Do not remove client instance when client open callbacks fails and
just clear __I40E_CLIENT_INSTANCE_OPENED bit. The driver also needs
to take care about this situation (when netdev is up and client
is NOT opened) in i40e_notify_client_of_netdev_close() and
calls client close callback only when __I40E_CLIENT_INSTANCE_OPENED
is set. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: mockup: fix NULL pointer dereference when removing debugfs
We now remove the device's debugfs entries when unbinding the driver.
This now causes a NULL-pointer dereference on module exit because the
platform devices are unregistered *after* the global debugfs directory
has been recursively removed. Fix it by unregistering the devices first. |
| In the Linux kernel, the following vulnerability has been resolved:
sfc: fix null pointer dereference in efx_hard_start_xmit
Trying to get the channel from the tx_queue variable here is wrong
because we can only be here if tx_queue is NULL, so we shouldn't
dereference it. As the above comment in the code says, this is very
unlikely to happen, but it's wrong anyway so let's fix it.
I hit this issue because of a different bug that caused tx_queue to be
NULL. If that happens, this is the error message that we get here:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[...]
RIP: 0010:efx_hard_start_xmit+0x153/0x170 [sfc] |
| In the Linux kernel, the following vulnerability has been resolved:
sfc/siena: fix null pointer dereference in efx_hard_start_xmit
Like in previous patch for sfc, prevent potential (but unlikely) NULL
pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: nci: fix possible NULL pointer dereference in send_acknowledge()
Handle memory allocation failure from nci_skb_alloc() (calling
alloc_skb()) to avoid possible NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: xhci: Check endpoint is valid before dereferencing it
When the host controller is not responding, all URBs queued to all
endpoints need to be killed. This can cause a kernel panic if we
dereference an invalid endpoint.
Fix this by using xhci_get_virt_ep() helper to find the endpoint and
checking if the endpoint is valid before dereferencing it.
[233311.853271] xhci-hcd xhci-hcd.1.auto: xHCI host controller not responding, assume dead
[233311.853393] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
[233311.853964] pc : xhci_hc_died+0x10c/0x270
[233311.853971] lr : xhci_hc_died+0x1ac/0x270
[233311.854077] Call trace:
[233311.854085] xhci_hc_died+0x10c/0x270
[233311.854093] xhci_stop_endpoint_command_watchdog+0x100/0x1a4
[233311.854105] call_timer_fn+0x50/0x2d4
[233311.854112] expire_timers+0xac/0x2e4
[233311.854118] run_timer_softirq+0x300/0xabc
[233311.854127] __do_softirq+0x148/0x528
[233311.854135] irq_exit+0x194/0x1a8
[233311.854143] __handle_domain_irq+0x164/0x1d0
[233311.854149] gic_handle_irq.22273+0x10c/0x188
[233311.854156] el1_irq+0xfc/0x1a8
[233311.854175] lpm_cpuidle_enter+0x25c/0x418 [msm_pm]
[233311.854185] cpuidle_enter_state+0x1f0/0x764
[233311.854194] do_idle+0x594/0x6ac
[233311.854201] cpu_startup_entry+0x7c/0x80
[233311.854209] secondary_start_kernel+0x170/0x198 |
| In the Linux kernel, the following vulnerability has been resolved:
gsmi: fix null-deref in gsmi_get_variable
We can get EFI variables without fetching the attribute, so we must
allow for that in gsmi.
commit 859748255b43 ("efi: pstore: Omit efivars caching EFI varstore
access layer") added a new get_variable call with attr=NULL, which
triggers panic in gsmi. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
It is possible that typec_register_partner() returns ERR_PTR on failure.
When port->partner is an error, a NULL pointer dereference may occur as
shown below.
[91222.095236][ T319] typec port0: failed to register partner (-17)
...
[91225.061491][ T319] Unable to handle kernel NULL pointer dereference
at virtual address 000000000000039f
[91225.274642][ T319] pc : tcpm_pd_data_request+0x310/0x13fc
[91225.274646][ T319] lr : tcpm_pd_data_request+0x298/0x13fc
[91225.308067][ T319] Call trace:
[91225.308070][ T319] tcpm_pd_data_request+0x310/0x13fc
[91225.308073][ T319] tcpm_pd_rx_handler+0x100/0x9e8
[91225.355900][ T319] kthread_worker_fn+0x178/0x58c
[91225.355902][ T319] kthread+0x150/0x200
[91225.355905][ T319] ret_from_fork+0x10/0x30
Add a check for port->partner to avoid dereferencing a NULL pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: mediatek: clk-mt7629-eth: Add check for mtk_alloc_clk_data
Add the check for the return value of mtk_alloc_clk_data() in order to
avoid NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: mediatek: clk-mt2701: Add check for mtk_alloc_clk_data
Add the check for the return value of mtk_alloc_clk_data() in order to
avoid NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: mediatek: clk-mt6779: Add check for mtk_alloc_clk_data
Add the check for the return value of mtk_alloc_clk_data() in order to
avoid NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: mediatek: clk-mt6765: Add check for mtk_alloc_clk_data
Add the check for the return value of mtk_alloc_clk_data() in order to
avoid NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
pstore/platform: Add check for kstrdup
Add check for the return value of kstrdup() and return the error
if it fails in order to avoid NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: mediatek: clk-mt6797: Add check for mtk_alloc_clk_data
Add the check for the return value of mtk_alloc_clk_data() in order to
avoid NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (axi-fan-control) Fix possible NULL pointer dereference
axi_fan_control_irq_handler(), dependent on the private
axi_fan_control_data structure, might be called before the hwmon
device is registered. That will cause an "Unable to handle kernel
NULL pointer dereference" error. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix null pointer dereference in error message
This patch fixes a null pointer dereference in the error message that is
printed when the Display Core (DC) fails to initialize. The original
message includes the DC version number, which is undefined if the DC is
not initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
drm: bridge: it66121: Fix invalid connector dereference
Fix the NULL pointer dereference when no monitor is connected, and the
sound card is opened from userspace.
Instead return an empty buffer (of zeroes) as the EDID information to
the sound framework if there is no connector attached. |
