| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ice: fix eswitch code memory leak in reset scenario
Add simple eswitch mode checker in attaching VF procedure and allocate
required port representor memory structures only in switchdev mode.
The reset flows triggers VF (if present) detach/attach procedure.
It might involve VF port representor(s) re-creation if the device is
configured is switchdev mode (not legacy one).
The memory was blindly allocated in current implementation,
regardless of the mode and not freed if in legacy mode.
Kmemeleak trace:
unreferenced object (percpu) 0x7e3bce5b888458 (size 40):
comm "bash", pid 1784, jiffies 4295743894
hex dump (first 32 bytes on cpu 45):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 0):
pcpu_alloc_noprof+0x4c4/0x7c0
ice_repr_create+0x66/0x130 [ice]
ice_repr_create_vf+0x22/0x70 [ice]
ice_eswitch_attach_vf+0x1b/0xa0 [ice]
ice_reset_all_vfs+0x1dd/0x2f0 [ice]
ice_pci_err_resume+0x3b/0xb0 [ice]
pci_reset_function+0x8f/0x120
reset_store+0x56/0xa0
kernfs_fop_write_iter+0x120/0x1b0
vfs_write+0x31c/0x430
ksys_write+0x61/0xd0
do_syscall_64+0x5b/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Testing hints (ethX is PF netdev):
- create at least one VF
echo 1 > /sys/class/net/ethX/device/sriov_numvfs
- trigger the reset
echo 1 > /sys/class/net/ethX/device/reset |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850
GCC_GCC_PCIE_HOT_RST is wrongly defined for WCN7850, causing kernel crash
on some specific platforms.
Since this register is divergent for WCN7850 and QCN9274, move it to
register table to allow different definitions. Then correct the register
address for WCN7850 to fix this issue.
Note IPQ5332 is not affected as it is not PCIe based device.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: cpu_ops_sbi: Use static array for boot_data
Since commit 6b9f29b81b15 ("riscv: Enable pcpu page first chunk
allocator"), if NUMA is enabled, the page percpu allocator may be used
on very sparse configurations, or when requested on boot with
percpu_alloc=page.
In that case, percpu data gets put in the vmalloc area. However,
sbi_hsm_hart_start() needs the physical address of a sbi_hart_boot_data,
and simply assumes that __pa() would work. This causes the just started
hart to immediately access an invalid address and hang.
Fortunately, struct sbi_hart_boot_data is not too large, so we can
simply allocate an array for boot_data statically, putting it in the
kernel image.
This fixes NUMA=y SMP boot on Sophgo SG2042.
To reproduce on QEMU: Set CONFIG_NUMA=y and CONFIG_DEBUG_VIRTUAL=y, then
run with:
qemu-system-riscv64 -M virt -smp 2 -nographic \
-kernel arch/riscv/boot/Image \
-append "percpu_alloc=page"
Kernel output:
[ 0.000000] Booting Linux on hartid 0
[ 0.000000] Linux version 6.16.0-rc1 (dram@sakuya) (riscv64-unknown-linux-gnu-gcc (GCC) 14.2.1 20250322, GNU ld (GNU Binutils) 2.44) #11 SMP Tue Jun 24 14:56:22 CST 2025
...
[ 0.000000] percpu: 28 4K pages/cpu s85784 r8192 d20712
...
[ 0.083192] smp: Bringing up secondary CPUs ...
[ 0.086722] ------------[ cut here ]------------
[ 0.086849] virt_to_phys used for non-linear address: (____ptrval____) (0xff2000000001d080)
[ 0.088001] WARNING: CPU: 0 PID: 1 at arch/riscv/mm/physaddr.c:14 __virt_to_phys+0xae/0xe8
[ 0.088376] Modules linked in:
[ 0.088656] CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.16.0-rc1 #11 NONE
[ 0.088833] Hardware name: riscv-virtio,qemu (DT)
[ 0.088948] epc : __virt_to_phys+0xae/0xe8
[ 0.089001] ra : __virt_to_phys+0xae/0xe8
[ 0.089037] epc : ffffffff80021eaa ra : ffffffff80021eaa sp : ff2000000004bbc0
[ 0.089057] gp : ffffffff817f49c0 tp : ff60000001d60000 t0 : 5f6f745f74726976
[ 0.089076] t1 : 0000000000000076 t2 : 705f6f745f747269 s0 : ff2000000004bbe0
[ 0.089095] s1 : ff2000000001d080 a0 : 0000000000000000 a1 : 0000000000000000
[ 0.089113] a2 : 0000000000000000 a3 : 0000000000000000 a4 : 0000000000000000
[ 0.089131] a5 : 0000000000000000 a6 : 0000000000000000 a7 : 0000000000000000
[ 0.089155] s2 : ffffffff8130dc00 s3 : 0000000000000001 s4 : 0000000000000001
[ 0.089174] s5 : ffffffff8185eff8 s6 : ff2000007f1eb000 s7 : ffffffff8002a2ec
[ 0.089193] s8 : 0000000000000001 s9 : 0000000000000001 s10: 0000000000000000
[ 0.089211] s11: 0000000000000000 t3 : ffffffff8180a9f7 t4 : ffffffff8180a9f7
[ 0.089960] t5 : ffffffff8180a9f8 t6 : ff2000000004b9d8
[ 0.089984] status: 0000000200000120 badaddr: ffffffff80021eaa cause: 0000000000000003
[ 0.090101] [<ffffffff80021eaa>] __virt_to_phys+0xae/0xe8
[ 0.090228] [<ffffffff8001d796>] sbi_cpu_start+0x6e/0xe8
[ 0.090247] [<ffffffff8001a5da>] __cpu_up+0x1e/0x8c
[ 0.090260] [<ffffffff8002a32e>] bringup_cpu+0x42/0x258
[ 0.090277] [<ffffffff8002914c>] cpuhp_invoke_callback+0xe0/0x40c
[ 0.090292] [<ffffffff800294e0>] __cpuhp_invoke_callback_range+0x68/0xfc
[ 0.090320] [<ffffffff8002a96a>] _cpu_up+0x11a/0x244
[ 0.090334] [<ffffffff8002aae6>] cpu_up+0x52/0x90
[ 0.090384] [<ffffffff80c09350>] bringup_nonboot_cpus+0x78/0x118
[ 0.090411] [<ffffffff80c11060>] smp_init+0x34/0xb8
[ 0.090425] [<ffffffff80c01220>] kernel_init_freeable+0x148/0x2e4
[ 0.090442] [<ffffffff80b83802>] kernel_init+0x1e/0x14c
[ 0.090455] [<ffffffff800124ca>] ret_from_fork_kernel+0xe/0xf0
[ 0.090471] [<ffffffff80b8d9c2>] ret_from_fork_kernel_asm+0x16/0x18
[ 0.090560] ---[ end trace 0000000000000000 ]---
[ 1.179875] CPU1: failed to come online
[ 1.190324] smp: Brought up 1 node, 1 CPU |
| In the Linux kernel, the following vulnerability has been resolved:
idpf: return 0 size for RSS key if not supported
Returning -EOPNOTSUPP from function returning u32 is leading to
cast and invalid size value as a result.
-EOPNOTSUPP as a size probably will lead to allocation fail.
Command: ethtool -x eth0
It is visible on all devices that don't have RSS caps set.
[ 136.615917] Call Trace:
[ 136.615921] <TASK>
[ 136.615927] ? __warn+0x89/0x130
[ 136.615942] ? __alloc_frozen_pages_noprof+0x322/0x330
[ 136.615953] ? report_bug+0x164/0x190
[ 136.615968] ? handle_bug+0x58/0x90
[ 136.615979] ? exc_invalid_op+0x17/0x70
[ 136.615987] ? asm_exc_invalid_op+0x1a/0x20
[ 136.616001] ? rss_prepare_get.constprop.0+0xb9/0x170
[ 136.616016] ? __alloc_frozen_pages_noprof+0x322/0x330
[ 136.616028] __alloc_pages_noprof+0xe/0x20
[ 136.616038] ___kmalloc_large_node+0x80/0x110
[ 136.616072] __kmalloc_large_node_noprof+0x1d/0xa0
[ 136.616081] __kmalloc_noprof+0x32c/0x4c0
[ 136.616098] ? rss_prepare_get.constprop.0+0xb9/0x170
[ 136.616105] rss_prepare_get.constprop.0+0xb9/0x170
[ 136.616114] ethnl_default_doit+0x107/0x3d0
[ 136.616131] genl_family_rcv_msg_doit+0x100/0x160
[ 136.616147] genl_rcv_msg+0x1b8/0x2c0
[ 136.616156] ? __pfx_ethnl_default_doit+0x10/0x10
[ 136.616168] ? __pfx_genl_rcv_msg+0x10/0x10
[ 136.616176] netlink_rcv_skb+0x58/0x110
[ 136.616186] genl_rcv+0x28/0x40
[ 136.616195] netlink_unicast+0x19b/0x290
[ 136.616206] netlink_sendmsg+0x222/0x490
[ 136.616215] __sys_sendto+0x1fd/0x210
[ 136.616233] __x64_sys_sendto+0x24/0x30
[ 136.616242] do_syscall_64+0x82/0x160
[ 136.616252] ? __sys_recvmsg+0x83/0xe0
[ 136.616265] ? syscall_exit_to_user_mode+0x10/0x210
[ 136.616275] ? do_syscall_64+0x8e/0x160
[ 136.616282] ? __count_memcg_events+0xa1/0x130
[ 136.616295] ? count_memcg_events.constprop.0+0x1a/0x30
[ 136.616306] ? handle_mm_fault+0xae/0x2d0
[ 136.616319] ? do_user_addr_fault+0x379/0x670
[ 136.616328] ? clear_bhb_loop+0x45/0xa0
[ 136.616340] ? clear_bhb_loop+0x45/0xa0
[ 136.616349] ? clear_bhb_loop+0x45/0xa0
[ 136.616359] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 136.616369] RIP: 0033:0x7fd30ba7b047
[ 136.616376] Code: 0c 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 80 3d bd d5 0c 00 00 41 89 ca 74 10 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 71 c3 55 48 83 ec 30 44 89 4c 24 2c 4c 89 44
[ 136.616381] RSP: 002b:00007ffde1796d68 EFLAGS: 00000202 ORIG_RAX: 000000000000002c
[ 136.616388] RAX: ffffffffffffffda RBX: 000055d7bd89f2a0 RCX: 00007fd30ba7b047
[ 136.616392] RDX: 0000000000000028 RSI: 000055d7bd89f3b0 RDI: 0000000000000003
[ 136.616396] RBP: 00007ffde1796e10 R08: 00007fd30bb4e200 R09: 000000000000000c
[ 136.616399] R10: 0000000000000000 R11: 0000000000000202 R12: 000055d7bd89f340
[ 136.616403] R13: 000055d7bd89f3b0 R14: 000055d78943f200 R15: 0000000000000000 |
| In the Linux kernel, the following vulnerability has been resolved:
net: netpoll: Initialize UDP checksum field before checksumming
commit f1fce08e63fe ("netpoll: Eliminate redundant assignment") removed
the initialization of the UDP checksum, which was wrong and broke
netpoll IPv6 transmission due to bad checksumming.
udph->check needs to be set before calling csum_ipv6_magic(). |
| In the Linux kernel, the following vulnerability has been resolved:
block: reject bs > ps block devices when THP is disabled
If THP is disabled and when a block device with logical block size >
page size is present, the following null ptr deref panic happens during
boot:
[ [13.2 mK AOSAN: null-ptr-deref in range [0x0000000000000000-0x0000000000K0 0 0[07]
[ 13.017749] RIP: 0010:create_empty_buffers+0x3b/0x380
<snip>
[ 13.025448] Call Trace:
[ 13.025692] <TASK>
[ 13.025895] block_read_full_folio+0x610/0x780
[ 13.026379] ? __pfx_blkdev_get_block+0x10/0x10
[ 13.027008] ? __folio_batch_add_and_move+0x1fa/0x2b0
[ 13.027548] ? __pfx_blkdev_read_folio+0x10/0x10
[ 13.028080] filemap_read_folio+0x9b/0x200
[ 13.028526] ? __pfx_filemap_read_folio+0x10/0x10
[ 13.029030] ? __filemap_get_folio+0x43/0x620
[ 13.029497] do_read_cache_folio+0x155/0x3b0
[ 13.029962] ? __pfx_blkdev_read_folio+0x10/0x10
[ 13.030381] read_part_sector+0xb7/0x2a0
[ 13.030805] read_lba+0x174/0x2c0
<snip>
[ 13.045348] nvme_scan_ns+0x684/0x850 [nvme_core]
[ 13.045858] ? __pfx_nvme_scan_ns+0x10/0x10 [nvme_core]
[ 13.046414] ? _raw_spin_unlock+0x15/0x40
[ 13.046843] ? __switch_to+0x523/0x10a0
[ 13.047253] ? kvm_clock_get_cycles+0x14/0x30
[ 13.047742] ? __pfx_nvme_scan_ns_async+0x10/0x10 [nvme_core]
[ 13.048353] async_run_entry_fn+0x96/0x4f0
[ 13.048787] process_one_work+0x667/0x10a0
[ 13.049219] worker_thread+0x63c/0xf60
As large folio support depends on THP, only allow bs > ps block devices
if THP is enabled. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: Intel: hda: Use devm_kstrdup() to avoid memleak.
sof_pdata->tplg_filename can have address allocated by kstrdup()
and can be overwritten. Memory leak was detected with kmemleak:
unreferenced object 0xffff88812391ff60 (size 16):
comm "kworker/4:1", pid 161, jiffies 4294802931
hex dump (first 16 bytes):
73 6f 66 2d 68 64 61 2d 67 65 6e 65 72 69 63 00 sof-hda-generic.
backtrace (crc 4bf1675c):
__kmalloc_node_track_caller_noprof+0x49c/0x6b0
kstrdup+0x46/0xc0
hda_machine_select.cold+0x1de/0x12cf [snd_sof_intel_hda_generic]
sof_init_environment+0x16f/0xb50 [snd_sof]
sof_probe_continue+0x45/0x7c0 [snd_sof]
sof_probe_work+0x1e/0x40 [snd_sof]
process_one_work+0x894/0x14b0
worker_thread+0x5e5/0xfb0
kthread+0x39d/0x760
ret_from_fork+0x31/0x70
ret_from_fork_asm+0x1a/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: fix runtime constant support for nommu kernels
the `__runtime_fixup_32` function does not handle the case where `val` is
zero correctly (as might occur when patching a nommu kernel and referring
to a physical address below the 4GiB boundary whose upper 32 bits are all
zero) because nothing in the existing logic prevents the code from taking
the `else` branch of both nop-checks and emitting two `nop` instructions.
This leaves random garbage in the register that is supposed to receive the
upper 32 bits of the pointer instead of zero that when combined with the
value for the lower 32 bits yields an invalid pointer and causes a kernel
panic when that pointer is eventually accessed.
The author clearly considered the fact that if the `lui` is converted into
a `nop` that the second instruction needs to be adjusted to become an `li`
instead of an `addi`, hence introducing the `addi_insn_mask` variable, but
didn't follow that logic through fully to the case where the `else` branch
executes. To fix it just adjust the logic to ensure that the second `else`
branch is not taken if the first instruction will be patched to a `nop`. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86/xen: Fix cleanup logic in emulation of Xen schedop poll hypercalls
kvm_xen_schedop_poll does a kmalloc_array() when a VM polls the host
for more than one event channel potr (nr_ports > 1).
After the kmalloc_array(), the error paths need to go through the
"out" label, but the call to kvm_read_guest_virt() does not.
[Adjusted commit message. - Paolo] |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: ad1816a: Fix potential NULL pointer deref in snd_card_ad1816a_pnp()
Use pr_warn() instead of dev_warn() when 'pdev' is NULL to avoid a
potential NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: rtsn: Fix a null pointer dereference in rtsn_probe()
Add check for the return value of rcar_gen4_ptp_alloc()
to prevent potential null pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7925: prevent NULL pointer dereference in mt7925_sta_set_decap_offload()
Add a NULL check for msta->vif before accessing its members to prevent
a kernel panic in AP mode deployment. This also fix the issue reported
in [1].
The crash occurs when this function is triggered before the station is
fully initialized. The call trace shows a page fault at
mt7925_sta_set_decap_offload() due to accessing resources when msta->vif
is NULL.
Fix this by adding an early return if msta->vif is NULL and also check
wcid.sta is ready. This ensures we only proceed with decap offload
configuration when the station's state is properly initialized.
[14739.655703] Unable to handle kernel paging request at virtual address ffffffffffffffa0
[14739.811820] CPU: 0 UID: 0 PID: 895854 Comm: hostapd Tainted: G
[14739.821394] Tainted: [C]=CRAP, [O]=OOT_MODULE
[14739.825746] Hardware name: Raspberry Pi 4 Model B Rev 1.1 (DT)
[14739.831577] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[14739.838538] pc : mt7925_sta_set_decap_offload+0xc0/0x1b8 [mt7925_common]
[14739.845271] lr : mt7925_sta_set_decap_offload+0x58/0x1b8 [mt7925_common]
[14739.851985] sp : ffffffc085efb500
[14739.855295] x29: ffffffc085efb500 x28: 0000000000000000 x27: ffffff807803a158
[14739.862436] x26: ffffff8041ececb8 x25: 0000000000000001 x24: 0000000000000001
[14739.869577] x23: 0000000000000001 x22: 0000000000000008 x21: ffffff8041ecea88
[14739.876715] x20: ffffff8041c19ca0 x19: ffffff8078031fe0 x18: 0000000000000000
[14739.883853] x17: 0000000000000000 x16: ffffffe2aeac1110 x15: 000000559da48080
[14739.890991] x14: 0000000000000001 x13: 0000000000000000 x12: 0000000000000000
[14739.898130] x11: 0a10020001008e88 x10: 0000000000001a50 x9 : ffffffe26457bfa0
[14739.905269] x8 : ffffff8042013bb0 x7 : ffffff807fb6cbf8 x6 : dead000000000100
[14739.912407] x5 : dead000000000122 x4 : ffffff80780326c8 x3 : 0000000000000000
[14739.919546] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffffff8041ececb8
[14739.926686] Call trace:
[14739.929130] mt7925_sta_set_decap_offload+0xc0/0x1b8 [mt7925_common]
[14739.935505] ieee80211_check_fast_rx+0x19c/0x510 [mac80211]
[14739.941344] _sta_info_move_state+0xe4/0x510 [mac80211]
[14739.946860] sta_info_move_state+0x1c/0x30 [mac80211]
[14739.952116] sta_apply_auth_flags.constprop.0+0x90/0x1b0 [mac80211]
[14739.958708] sta_apply_parameters+0x234/0x5e0 [mac80211]
[14739.964332] ieee80211_add_station+0xdc/0x190 [mac80211]
[14739.969950] nl80211_new_station+0x46c/0x670 [cfg80211]
[14739.975516] genl_family_rcv_msg_doit+0xdc/0x150
[14739.980158] genl_rcv_msg+0x218/0x298
[14739.983830] netlink_rcv_skb+0x64/0x138
[14739.987670] genl_rcv+0x40/0x60
[14739.990816] netlink_unicast+0x314/0x380
[14739.994742] netlink_sendmsg+0x198/0x3f0
[14739.998664] __sock_sendmsg+0x64/0xc0
[14740.002324] ____sys_sendmsg+0x260/0x298
[14740.006242] ___sys_sendmsg+0xb4/0x110 |
| In the Linux kernel, the following vulnerability has been resolved:
dm-bufio: fix sched in atomic context
If "try_verify_in_tasklet" is set for dm-verity, DM_BUFIO_CLIENT_NO_SLEEP
is enabled for dm-bufio. However, when bufio tries to evict buffers, there
is a chance to trigger scheduling in spin_lock_bh, the following warning
is hit:
BUG: sleeping function called from invalid context at drivers/md/dm-bufio.c:2745
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 123, name: kworker/2:2
preempt_count: 201, expected: 0
RCU nest depth: 0, expected: 0
4 locks held by kworker/2:2/123:
#0: ffff88800a2d1548 ((wq_completion)dm_bufio_cache){....}-{0:0}, at: process_one_work+0xe46/0x1970
#1: ffffc90000d97d20 ((work_completion)(&dm_bufio_replacement_work)){....}-{0:0}, at: process_one_work+0x763/0x1970
#2: ffffffff8555b528 (dm_bufio_clients_lock){....}-{3:3}, at: do_global_cleanup+0x1ce/0x710
#3: ffff88801d5820b8 (&c->spinlock){....}-{2:2}, at: do_global_cleanup+0x2a5/0x710
Preemption disabled at:
[<0000000000000000>] 0x0
CPU: 2 UID: 0 PID: 123 Comm: kworker/2:2 Not tainted 6.16.0-rc3-g90548c634bd0 #305 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
Workqueue: dm_bufio_cache do_global_cleanup
Call Trace:
<TASK>
dump_stack_lvl+0x53/0x70
__might_resched+0x360/0x4e0
do_global_cleanup+0x2f5/0x710
process_one_work+0x7db/0x1970
worker_thread+0x518/0xea0
kthread+0x359/0x690
ret_from_fork+0xf3/0x1b0
ret_from_fork_asm+0x1a/0x30
</TASK>
That can be reproduced by:
veritysetup format --data-block-size=4096 --hash-block-size=4096 /dev/vda /dev/vdb
SIZE=$(blockdev --getsz /dev/vda)
dmsetup create myverity -r --table "0 $SIZE verity 1 /dev/vda /dev/vdb 4096 4096 <data_blocks> 1 sha256 <root_hash> <salt> 1 try_verify_in_tasklet"
mount /dev/dm-0 /mnt -o ro
echo 102400 > /sys/module/dm_bufio/parameters/max_cache_size_bytes
[read files in /mnt] |
| In the Linux kernel, the following vulnerability has been resolved:
tracing/osnoise: Fix crash in timerlat_dump_stack()
We have observed kernel panics when using timerlat with stack saving,
with the following dmesg output:
memcpy: detected buffer overflow: 88 byte write of buffer size 0
WARNING: CPU: 2 PID: 8153 at lib/string_helpers.c:1032 __fortify_report+0x55/0xa0
CPU: 2 UID: 0 PID: 8153 Comm: timerlatu/2 Kdump: loaded Not tainted 6.15.3-200.fc42.x86_64 #1 PREEMPT(lazy)
Call Trace:
<TASK>
? trace_buffer_lock_reserve+0x2a/0x60
__fortify_panic+0xd/0xf
__timerlat_dump_stack.cold+0xd/0xd
timerlat_dump_stack.part.0+0x47/0x80
timerlat_fd_read+0x36d/0x390
vfs_read+0xe2/0x390
? syscall_exit_to_user_mode+0x1d5/0x210
ksys_read+0x73/0xe0
do_syscall_64+0x7b/0x160
? exc_page_fault+0x7e/0x1a0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
__timerlat_dump_stack() constructs the ftrace stack entry like this:
struct stack_entry *entry;
...
memcpy(&entry->caller, fstack->calls, size);
entry->size = fstack->nr_entries;
Since commit e7186af7fb26 ("tracing: Add back FORTIFY_SOURCE logic to
kernel_stack event structure"), struct stack_entry marks its caller
field with __counted_by(size). At the time of the memcpy, entry->size
contains garbage from the ringbuffer, which under some circumstances is
zero, triggering a kernel panic by buffer overflow.
Populate the size field before the memcpy so that the out-of-bounds
check knows the correct size. This is analogous to
__ftrace_trace_stack(). |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix race between cache write completion and ALL_QUEUED being set
When netfslib is issuing subrequests, the subrequests start processing
immediately and may complete before we reach the end of the issuing
function. At the end of the issuing function we set NETFS_RREQ_ALL_QUEUED
to indicate to the collector that we aren't going to issue any more subreqs
and that it can do the final notifications and cleanup.
Now, this isn't a problem if the request is synchronous
(NETFS_RREQ_OFFLOAD_COLLECTION is unset) as the result collection will be
done in-thread and we're guaranteed an opportunity to run the collector.
However, if the request is asynchronous, collection is primarily triggered
by the termination of subrequests queuing it on a workqueue. Now, a race
can occur here if the app thread sets ALL_QUEUED after the last subrequest
terminates.
This can happen most easily with the copy2cache code (as used by Ceph)
where, in the collection routine of a read request, an asynchronous write
request is spawned to copy data to the cache. Folios are added to the
write request as they're unlocked, but there may be a delay before
ALL_QUEUED is set as the write subrequests may complete before we get
there.
If all the write subreqs have finished by the ALL_QUEUED point, no further
events happen and the collection never happens, leaving the request
hanging.
Fix this by queuing the collector after setting ALL_QUEUED. This is a bit
heavy-handed and it may be sufficient to do it only if there are no extant
subreqs.
Also add a tracepoint to cross-reference both requests in a copy-to-request
operation and add a trace to the netfs_rreq tracepoint to indicate the
setting of ALL_QUEUED. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/bpf: Fix bpf_arch_text_poke() with new_addr == NULL again
Commit 7ded842b356d ("s390/bpf: Fix bpf_plt pointer arithmetic") has
accidentally removed the critical piece of commit c730fce7c70c
("s390/bpf: Fix bpf_arch_text_poke() with new_addr == NULL"), causing
intermittent kernel panics in e.g. perf's on_switch() prog to reappear.
Restore the fix and add a comment. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: backend: fix out-of-bound write
The buffer is set to 80 character. If a caller write more characters,
count is truncated to the max available space in "simple_write_to_buffer".
But afterwards a string terminator is written to the buffer at offset count
without boundary check. The zero termination is written OUT-OF-BOUND.
Add a check that the given buffer is smaller then the buffer to prevent. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: reject VHT opmode for unsupported channel widths
VHT operating mode notifications are not defined for channel widths
below 20 MHz. In particular, 5 MHz and 10 MHz are not valid under the
VHT specification and must be rejected.
Without this check, malformed notifications using these widths may
reach ieee80211_chan_width_to_rx_bw(), leading to a WARN_ON due to
invalid input. This issue was reported by syzbot.
Reject these unsupported widths early in sta_link_apply_parameters()
when opmode_notif is used. The accepted set includes 20, 40, 80, 160,
and 80+80 MHz, which are valid for VHT. While 320 MHz is not defined
for VHT, it is allowed to avoid rejecting HE or EHT clients that may
still send a VHT opmode notification. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: nintendo: avoid bluetooth suspend/resume stalls
Ensure we don't stall or panic the kernel when using bluetooth-connected
controllers. This was reported as an issue on android devices using
kernel 6.6 due to the resume hook which had been added for usb joycons.
First, set a new state value to JOYCON_CTLR_STATE_SUSPENDED in a
newly-added nintendo_hid_suspend. This makes sure we will not stall out
the kernel waiting for input reports during led classdev suspend. The
stalls could happen if connectivity is unreliable or lost to the
controller prior to suspend.
Second, since we lose connectivity during suspend, do not try
joycon_init() for bluetooth controllers in the nintendo_hid_resume path.
Tested via multiple suspend/resume flows when using the controller both
in USB and bluetooth modes. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: Allow CPU to reschedule while setting per-page memory attributes
When running an SEV-SNP guest with a sufficiently large amount of memory (1TB+),
the host can experience CPU soft lockups when running an operation in
kvm_vm_set_mem_attributes() to set memory attributes on the whole
range of guest memory.
watchdog: BUG: soft lockup - CPU#8 stuck for 26s! [qemu-kvm:6372]
CPU: 8 UID: 0 PID: 6372 Comm: qemu-kvm Kdump: loaded Not tainted 6.15.0-rc7.20250520.el9uek.rc1.x86_64 #1 PREEMPT(voluntary)
Hardware name: Oracle Corporation ORACLE SERVER E4-2c/Asm,MB Tray,2U,E4-2c, BIOS 78016600 11/13/2024
RIP: 0010:xas_create+0x78/0x1f0
Code: 00 00 00 41 80 fc 01 0f 84 82 00 00 00 ba 06 00 00 00 bd 06 00 00 00 49 8b 45 08 4d 8d 65 08 41 39 d6 73 20 83 ed 06 48 85 c0 <74> 67 48 89 c2 83 e2 03 48 83 fa 02 75 0c 48 3d 00 10 00 00 0f 87
RSP: 0018:ffffad890a34b940 EFLAGS: 00000286
RAX: ffff96f30b261daa RBX: ffffad890a34b9c8 RCX: 0000000000000000
RDX: 000000000000001e RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000018 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffffad890a356868
R13: ffffad890a356860 R14: 0000000000000000 R15: ffffad890a356868
FS: 00007f5578a2a400(0000) GS:ffff97ed317e1000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f015c70fb18 CR3: 00000001109fd006 CR4: 0000000000f70ef0
PKRU: 55555554
Call Trace:
<TASK>
xas_store+0x58/0x630
__xa_store+0xa5/0x130
xa_store+0x2c/0x50
kvm_vm_set_mem_attributes+0x343/0x710 [kvm]
kvm_vm_ioctl+0x796/0xab0 [kvm]
__x64_sys_ioctl+0xa3/0xd0
do_syscall_64+0x8c/0x7a0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f5578d031bb
Code: ff ff ff 85 c0 79 9b 49 c7 c4 ff ff ff ff 5b 5d 4c 89 e0 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 2d 4c 0f 00 f7 d8 64 89 01 48
RSP: 002b:00007ffe0a742b88 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 000000004020aed2 RCX: 00007f5578d031bb
RDX: 00007ffe0a742c80 RSI: 000000004020aed2 RDI: 000000000000000b
RBP: 0000010000000000 R08: 0000010000000000 R09: 0000017680000000
R10: 0000000000000080 R11: 0000000000000246 R12: 00005575e5f95120
R13: 00007ffe0a742c80 R14: 0000000000000008 R15: 00005575e5f961e0
While looping through the range of memory setting the attributes,
call cond_resched() to give the scheduler a chance to run a higher
priority task on the runqueue if necessary and avoid staying in
kernel mode long enough to trigger the lockup. |
